Yuanfang Chen
School of Materials Science and Engineering, Chongqing university of technology, Chongqing, China
Hongbin Xu
School of Materials Science and Engineering, Chongqing university of technology, Chongqing, China
Huade Jiang
School of Materials Science and Engineering, Chongqing university of technology, Chongqing, China
Guohua Guan
School of Materials Science and Engineering, Chongqing university of technology, Chongqing, China
ABSTRACT
The hot compression experiments were carried out on Gleeble-1500D thermal simulator system and the hot deformation performance of non-quenched and tempered steel 49MnVS3 between 950°C∼1200°C with strain rate of 0.1~10 sec-1 were investigated by processing maps of dynamic material model. The deformation zone where dynamic recovery and dynamic recrystallization occurred is obtained according to true stress-strain curve. The variation law of strain rate sensitive factor m and power dissipation η is analyzed. Based on the analysis on m,η and instability criterion , the instability zone with strain of 0.3 and 0.5 is analyzed by contrastive analysis method. It is found that the hot processing safety zone of this metal accords to each other. Taking the deformation parameters when dynamic recrystallization happened in hot processing safety zone as deformation conditions, the optimal processing safety zones of this alloy are determined to be 2~10 sec-1 for strain rate and 1150~1200°C for processing temperature.
PDF References Citation
How to cite this article
Yuanfang Chen, Hongbin Xu, Huade Jiang and Guohua Guan, 2013. Deformation Performance at High Temperature and Processing Maps of 49 MnVS3. Journal of Applied Sciences, 13: 1716-1721.
DOI: 10.3923/jas.2013.1716.1721
URL: https://scialert.net/abstract/?doi=jas.2013.1716.1721
DOI: 10.3923/jas.2013.1716.1721
URL: https://scialert.net/abstract/?doi=jas.2013.1716.1721
REFERENCES
- Prasad, Y.V.R.K. and K.P. Rao, 2008. Processing maps for hot deformation of rolled AZ31 magnesium alloy plate: Anisotropy of hot workability. Mater. Sci. Eng. A, 487: 316-327.
CrossRefDirect Link - Prasad, Y.V.R.K. and K.P. Rao, 2005. Processing maps and rate controlling mechanisms of hot deformation of electrolytic tough pitch copper in the temperature range 300-950 ○C. Mater. Sci. Eng. A, 391: 141-150.
CrossRefDirect Link - Prasad, Y.V.R.K., H.L. Gegel, S.M. Doraivelu, J.C. Malas, J.T. Morgan, K.A. Lark and D.R. Barker, 1984. Modeling of dynamic material behavior in hot deformation: Forging of Ti-6242. Metallurgical Trans. A, 15: 1883-1892.
CrossRef - Ganesan, G., K. Raghukandan, R. Karthikeyan and B.C. Pai, 2005. Development of processing map for 6061 Al/15% SiCp through neural networks. J. Mater. Process. Technol., 166: 423-429.
CrossRefDirect Link - Meng, G., B.L. Li, H.M. Li, H. Huang and Z. Nie, 2009. Hot deformation and processing maps of an Al-5.7 wt.%Mg alloy with erbium. Mater. Sci. Eng. A, 517: 132-137.
CrossRefDirect Link - Momeni, A. and K. Dehghani, 2010. Characterization of hot deformation behavior of 410 martensitic stainless steel using constitutive equations and processing maps. Mater. Sci. Eng. A, 527: 5467-5473.
CrossRefDirect Link - Kim, H.Y., H.C. Kwon, H.W. Lee, Y.T. Im, S.M. Byon and H.D. Park, 2008. Processing map approach for surface defect prediction in the hot bar rolling. J. Mater. Process. Technol., 205: 70-80.
CrossRefDirect Link - Tan, C.W., S.N. Xu, L. Wang, Z.Y. Chen, F.C. Wang and H,N. Cai, 2007. Effect of temperature on mechanical behavior of AZ31 magnesium alloy. Trans. Nonferrous Met. Soc. China, 17: 41-45.
CrossRefDirect Link - Bozzini, B. and E. Cerri, 2002. Numerical reliability of hot working processing maps. Mater. Sci. Eng. A, 328: 344-347.
CrossRefDirect Link - Cavaliere, P., 2002. Hot and warm forming of 2618 aluminium alloy. J. Light Metals, 2: 247-252.
CrossRef - Gronostajski, Z., 2002. The deformation processing map for control of microstructure in CuAl9.2Fe3 aluminium bronze. J. Mater. Process. Technol., 125-126: 119-124.
CrossRefDirect Link