HOME JOURNALS CONTACT

Journal of Applied Sciences

Year: 2013 | Volume: 13 | Issue: 10 | Page No.: 1716-1721
DOI: 10.3923/jas.2013.1716.1721
Deformation Performance at High Temperature and Processing Maps of 49 MnVS3
Yuanfang Chen, Hongbin Xu, Huade Jiang and Guohua Guan

Abstract: The hot compression experiments were carried out on Gleeble-1500D thermal simulator system and the hot deformation performance of non-quenched and tempered steel 49MnVS3 between 950°C∼1200°C with strain rate of 0.1~10 sec-1 were investigated by processing maps of dynamic material model. The deformation zone where dynamic recovery and dynamic recrystallization occurred is obtained according to true stress-strain curve. The variation law of strain rate sensitive factor m and power dissipation η is analyzed. Based on the analysis on m,η and instability criterion , the instability zone with strain of 0.3 and 0.5 is analyzed by contrastive analysis method. It is found that the hot processing safety zone of this metal accords to each other. Taking the deformation parameters when dynamic recrystallization happened in hot processing safety zone as deformation conditions, the optimal processing safety zones of this alloy are determined to be 2~10 sec-1 for strain rate and 1150~1200°C for processing temperature.

Fulltext PDF

How to cite this article
Yuanfang Chen, Hongbin Xu, Huade Jiang and Guohua Guan, 2013. Deformation Performance at High Temperature and Processing Maps of 49 MnVS3. Journal of Applied Sciences, 13: 1716-1721.

Keywords: power dissipation efficiency, Non-quenched and tempered steel, hot compression, strain rate sensitive factor and processing maps

REFERENCES
  • Chen, Y.B., W. Ma and K. Jin, 2001. Development on improving the strength and toughness of microalloyed steels. Mater. Mech. Eng., 25: 1-6.

  • Tang, X.M., J.Y. Chen, J.G. Zhao and H.Z. Ao, 2001. Development and application of non-quenched and tempered steels of bending and extending arms. Heat Treatment Metals, 1: 45-47.

  • Prasad, Y.V.R.K. and K.P. Rao, 2008. Processing maps for hot deformation of rolled AZ31 magnesium alloy plate: Anisotropy of hot workability. Mater. Sci. Eng. A, 487: 316-327.
    CrossRef    Direct Link    

  • Prasad, Y.V.R.K. and K.P. Rao, 2005. Processing maps and rate controlling mechanisms of hot deformation of electrolytic tough pitch copper in the temperature range 300-950 ○C. Mater. Sci. Eng. A, 391: 141-150.
    CrossRef    Direct Link    

  • Prasad, Y.V.R.K., H.L. Gegel, S.M. Doraivelu, J.C. Malas, J.T. Morgan, K.A. Lark and D.R. Barker, 1984. Modeling of dynamic material behavior in hot deformation: Forging of Ti-6242. Metallurgical Trans. A, 15: 1883-1892.
    CrossRef    

  • Ganesan, G., K. Raghukandan, R. Karthikeyan and B.C. Pai, 2005. Development of processing map for 6061 Al/15% SiCp through neural networks. J. Mater. Process. Technol., 166: 423-429.
    CrossRef    Direct Link    

  • Meng, G., B.L. Li, H.M. Li, H. Huang and Z. Nie, 2009. Hot deformation and processing maps of an Al-5.7 wt.%Mg alloy with erbium. Mater. Sci. Eng. A, 517: 132-137.
    CrossRef    Direct Link    

  • Ziegler, H., 1983. An Introduction to Thermomechanics. North-Holland Publishing Company, Amsterdam, New York, Oxford

  • Zheng, Q.G., Y. Wang and Y.W. Zhang, 2011. Construction for processing map based on DMM and identification for the stable hot-working parameters of Ti-6Al-2Zr-1Mo-1V alloy. J. Funct. Mater., 42: 2301-2306.

  • Momeni, A. and K. Dehghani, 2010. Characterization of hot deformation behavior of 410 martensitic stainless steel using constitutive equations and processing maps. Mater. Sci. Eng. A, 527: 5467-5473.
    CrossRef    Direct Link    

  • Kim, H.Y., H.C. Kwon, H.W. Lee, Y.T. Im, S.M. Byon and H.D. Park, 2008. Processing map approach for surface defect prediction in the hot bar rolling. J. Mater. Process. Technol., 205: 70-80.
    CrossRef    Direct Link    

  • Tan, C.W., S.N. Xu, L. Wang, Z.Y. Chen, F.C. Wang and H,N. Cai, 2007. Effect of temperature on mechanical behavior of AZ31 magnesium alloy. Trans. Nonferrous Met. Soc. China, 17: 41-45.
    CrossRef    Direct Link    

  • Bozzini, B. and E. Cerri, 2002. Numerical reliability of hot working processing maps. Mater. Sci. Eng. A, 328: 344-347.
    CrossRef    Direct Link    

  • Cavaliere, P., 2002. Hot and warm forming of 2618 aluminium alloy. J. Light Metals, 2: 247-252.
    CrossRef    

  • Gronostajski, Z., 2002. The deformation processing map for control of microstructure in CuAl9.2Fe3 aluminium bronze. J. Mater. Process. Technol., 125-126: 119-124.
    CrossRef    Direct Link    

    • © Science Alert. All Rights Reserved