Subscribe Now Subscribe Today
Research Article
 

Deformation Performance at High Temperature and Processing Maps of 49 MnVS3



Yuanfang Chen, Hongbin Xu, Huade Jiang and Guohua Guan
 
ABSTRACT

The hot compression experiments were carried out on Gleeble-1500D thermal simulator system and the hot deformation performance of non-quenched and tempered steel 49MnVS3 between 950°C∼1200°C with strain rate of 0.1~10 sec-1 were investigated by processing maps of dynamic material model. The deformation zone where dynamic recovery and dynamic recrystallization occurred is obtained according to true stress-strain curve. The variation law of strain rate sensitive factor m and power dissipation η is analyzed. Based on the analysis on m,η and instability criterion , the instability zone with strain of 0.3 and 0.5 is analyzed by contrastive analysis method. It is found that the hot processing safety zone of this metal accords to each other. Taking the deformation parameters when dynamic recrystallization happened in hot processing safety zone as deformation conditions, the optimal processing safety zones of this alloy are determined to be 2~10 sec-1 for strain rate and 1150~1200°C for processing temperature.

Services
Related Articles in ASCI
Similar Articles in this Journal
Search in Google Scholar
View Citation
Report Citation

 
  How to cite this article:

Yuanfang Chen, Hongbin Xu, Huade Jiang and Guohua Guan, 2013. Deformation Performance at High Temperature and Processing Maps of 49 MnVS3. Journal of Applied Sciences, 13: 1716-1721.

DOI: 10.3923/jas.2013.1716.1721

URL: https://scialert.net/abstract/?doi=jas.2013.1716.1721

REFERENCES
Bozzini, B. and E. Cerri, 2002. Numerical reliability of hot working processing maps. Mater. Sci. Eng. A, 328: 344-347.
CrossRef  |  Direct Link  |  

Cavaliere, P., 2002. Hot and warm forming of 2618 aluminium alloy. J. Light Metals, 2: 247-252.
CrossRef  |  

Chen, Y.B., W. Ma and K. Jin, 2001. Development on improving the strength and toughness of microalloyed steels. Mater. Mech. Eng., 25: 1-6.

Ganesan, G., K. Raghukandan, R. Karthikeyan and B.C. Pai, 2005. Development of processing map for 6061 Al/15% SiCp through neural networks. J. Mater. Process. Technol., 166: 423-429.
CrossRef  |  Direct Link  |  

Gronostajski, Z., 2002. The deformation processing map for control of microstructure in CuAl9.2Fe3 aluminium bronze. J. Mater. Process. Technol., 125-126: 119-124.
CrossRef  |  Direct Link  |  

Kim, H.Y., H.C. Kwon, H.W. Lee, Y.T. Im, S.M. Byon and H.D. Park, 2008. Processing map approach for surface defect prediction in the hot bar rolling. J. Mater. Process. Technol., 205: 70-80.
CrossRef  |  Direct Link  |  

Meng, G., B.L. Li, H.M. Li, H. Huang and Z. Nie, 2009. Hot deformation and processing maps of an Al-5.7 wt.%Mg alloy with erbium. Mater. Sci. Eng. A, 517: 132-137.
CrossRef  |  Direct Link  |  

Momeni, A. and K. Dehghani, 2010. Characterization of hot deformation behavior of 410 martensitic stainless steel using constitutive equations and processing maps. Mater. Sci. Eng. A, 527: 5467-5473.
CrossRef  |  Direct Link  |  

Prasad, Y.V.R.K. and K.P. Rao, 2005. Processing maps and rate controlling mechanisms of hot deformation of electrolytic tough pitch copper in the temperature range 300-950 C. Mater. Sci. Eng. A, 391: 141-150.
CrossRef  |  Direct Link  |  

Prasad, Y.V.R.K. and K.P. Rao, 2008. Processing maps for hot deformation of rolled AZ31 magnesium alloy plate: Anisotropy of hot workability. Mater. Sci. Eng. A, 487: 316-327.
CrossRef  |  Direct Link  |  

Prasad, Y.V.R.K., H.L. Gegel, S.M. Doraivelu, J.C. Malas, J.T. Morgan, K.A. Lark and D.R. Barker, 1984. Modeling of dynamic material behavior in hot deformation: Forging of Ti-6242. Metallurgical Trans. A, 15: 1883-1892.
CrossRef  |  

Tan, C.W., S.N. Xu, L. Wang, Z.Y. Chen, F.C. Wang and H,N. Cai, 2007. Effect of temperature on mechanical behavior of AZ31 magnesium alloy. Trans. Nonferrous Met. Soc. China, 17: 41-45.
CrossRef  |  Direct Link  |  

Tang, X.M., J.Y. Chen, J.G. Zhao and H.Z. Ao, 2001. Development and application of non-quenched and tempered steels of bending and extending arms. Heat Treatment Metals, 1: 45-47.

Zheng, Q.G., Y. Wang and Y.W. Zhang, 2011. Construction for processing map based on DMM and identification for the stable hot-working parameters of Ti-6Al-2Zr-1Mo-1V alloy. J. Funct. Mater., 42: 2301-2306.

Ziegler, H., 1983. An Introduction to Thermomechanics. North-Holland Publishing Company, Amsterdam, New York, Oxford.

©  2019 Science Alert. All Rights Reserved