Quality Assessment of Borehole Water used in the Vicinities of Benin, Edo State and Agbor, Delta State of Nigeria
This study was aimed at determining water quality parameters in borehole water from the University of Benin, Benin City, Okobi and Eluemelor vicinities of Agbor respectively in order to access the quality of the borehole water from the three boreholes. Water samples were collected three times at monthly intervals between December 2009 and February 2010 for the three sampling points, respectively. Parameters for quality check includes; pH, temperature, electrical conductivity, biochemical oxygen demand, dissolved oxygen, chloride, sulphate, nitrate, ammonium, sodium, calcium, magnesium, lead, cadmium, copper, zinc, chromium, iron, arsenic, nickel and manganese. Physicochemical characteristics were determined using their respective standard methods of analysis while heavy metal levels were determined using Atomic Absorption Spectrophotometer. Parameters determined gave results which fell within the World Health Organisation (WHO) and federal environmental protection agency (permissible limit for portable water except for calcium and manganese which gave elevated values as against their corresponding WHO limits of 75 and 0.05 mg L-1, respectively. The pollution index values for calcium and manganese indicated significant degree of pollution by the two metals in all the borehole water samples studied. The overall results from this study showed that water samples from the boreholes studied were found to be safe for drinking and other domestic activities considering the parameters which fell within the allowable limits. However, proactive measures must be taken to check the levels of calcium and manganese to avert severe contamination and protect our precious ground water resource. It is therefore recommended that the borehole water from the three boreholes studied be subjected to treatment processes to reduce calcium and manganese levels before exposure to public use.
July 29, 2010; Accepted: January 19, 2011;
Published: April 22, 2011
Contamination of water bodies has increasingly become an issue of serious environmental
concern. Clean water is a priceless and limited resource that man has began
to treasure only recently after decades of pollution and waste (Silderberg,
2003). Potable water is an essential ingredient for good health and the
socio-economic development of man (Udom et al., 2002),
but it is lacking in many societies. All natural waters contain many dissolved
substances. Contaminants such as bacteria, viruses, heavy metals, nitrates and
salt have polluted water supplies as a result of inadequate treatment and disposal
of waste from humans and livestock, industrial discharges, and over-use of limited
water resources (Singh and Mosley, 2003).
The major sources of pollution in streams, rivers and underground water arises
from anthropogenic activities largely caused by the poor and uncultured living
habit of people as well as the unhealthy practices of factories, industries
and corporate bodies; resulting in the discharge of effluents and untreated
wastes. Pollution in water affects not only water quality but could also be
dangerous to aquatic life (Sunnudo-Wilhelmy and Gill, 1999).
Ground water pollution could be avoided when borehole wells are located far
from any source of potential pollution. Good well design is also important in
the prevention of underground water pollution. During the construction process
of a borehole, drilling fluids, chemical casings and other materials may find
their way into the well thereby polluting the water. An open hole during the
construction stage can also be a direct route for contaminants from the surface
to the aquifer thereby providing an ideal opportunity for chemical and bacteriological
pollution to occur. Lasting damage can be avoided if the well is completed,
disinfected and piped within a short space of time. The possibility of contamination
increases if there is a lengthy delay in completing the well. Even if no sources
of anthropogenic contamination exist, there is potential for natural levels
of metals and other chemicals to be harmful to human health. This was highlighted
in Bangladesh where natural levels of arsenic in groundwater were found to be
causing harmful effects on the population (Anawara et al.,
2002). Unfortunately, this problem arose because the groundwater was extracted
for drinking without a detailed chemical investigation. Monitoring the quality
of water is very essential for environmental safety. The natural water analyses
for physical and chemical properties including trace element contents are very
important for public health studies (Kot et al., 2000).
These studies are also a main part of pollution studies in the environment.
Borehole water serves as the major source of drinking water in the local population of Nigeria, since only very few can afford and rely on purified and treated bottled water for consumption. Owners of boreholes capitalise on this opportunity to commercialize their boreholes which many resort to buying the bore hole water for drinking, since it is cheaper for them to afford.
Therefore, this brings the imperativeness of examining the water quality parameters of borehole water with special interest study on Agbor town in Delta State and Benin City in Edo State respectively with a view to accessing their level of purity. This study tends to x-ray and estimate the levels of heavy metals, ion contents, biochemical oxygen demand, dissolved oxygen as well as other parameters such as temperature, pH, conductivity with a view to comparing them with international allowable standards as this will guide our decision on the quality and purity assessment of the bore holes.
MATERIALS AND METHODS
Study area: Geographically, the study area comprises of Edo and Delta
state, respectively. Borehole water was collected from the borehole in the University
of Benin, Benin City, Edo State as well as two different locations in Agbor
town, Delta State. The two locations in Agbor were borehole was obtained are
Okobi Street, Boji-Boji Owa and Eluemelor, Agbor Urban. These areas were specifically
chosen for the study because of the very low water table observed and lack of
nearness to industrial facilities and potential ground water pollution sites
such as urban solid waste dump sites.
Sample collection treatment and preservation: Two sample points were
located in Agbor (Fig. 1) while one located in Benin. Borehole
water samples for the study were collected three times at monthly intervals
between December 2009 to February 2010 for the three sampling points, respectively.
|| Map of agbor showing study area
Water samples were collected directly from the taps in the borehole into clean
white polyethylene stoppered bottles which have been washed with soap solution,
rinsed three times with pure water and then rinsed again three times with 1%
HNO3 after which they were rinsed with the bore hole water to be
collected. The water samples were stoppered and labelled.
The samples were filtered by passing water through a 0.45 mm millipore membrane
filter placed in an all glass millipore filtering system. The membrane filters
have been washed with 1% HNO3 followed by rinsing in high purity
water prior to filtration (Meranger et al., 1979). Samples
were there after refrigerated at 4°C in the laboratory prior to analysis.
Sample analysis: Samples for Dissolved Oxygen (DO) and Bological Oxygen
Dmand (BOD) were determined using Winkler method by treating with manganesous
sulphate solution, alkali-iodide azide solution and 1.00 mL concentrated sulphuric
acid by inserting the can for several times. The samples were then allowed to
stay for five minutes after the formation of brown precipitates. The DO was
immediately determined in-situ using a multi-parameter water quality model (model
6000 UPG), the remaining treated solution was well stoppered and incubated prior
to five days later before BOD analysis. BOD was determined using iodometric
method (USEPA 1986; Young et al.,
1981). Analysis for heavy metal determination was achieved by measuring
100 mL of each water sample into a beaker and 5 cm3 of concentrated
HNO3 was added. The solution was evaporated to near dryness on a
hot plate, making sure that the sample does not boil. The beaker containing
the residue was cooled. 5 mL of conc. HNO3 was further added and
returned to the hot plate until digestion was completed (Ahn
et al., 1996; Anonymous 1995). Two millilitter of
conc. HNO3 was added and the beaker warmed slightly to dissolve the
residue. The digested sample was filtered and the filtrate made up to 50 cm3
mark with deionized water. The solutions were stored in a refrigerator prior
to metal analysis using atomic absorption spectrophotometer. Blanks were also
prepared using the same procedure of digestion of the samples. Parameters such
as pH, temperature, electrical conductivity, BOD, DO and ion contents (Cl¯,
NO3¯, NH4+, Na+, Ca2+,
Mg2+, SO42¯) were all determined by standard
methods (Ademoroti, 1986; Anonymous
1995; APHA 1992; Chapeon, 1992;
Franson, 1995). The temperature, pH and electrical conductivity
were determined with zeal thermometer (0-300°C), P107 digital consort pH
meter and K 120 digital consort electronic conductometer respectively. Metal
concentrations were determined using atomic absorption spectrophotometer (210VGP
model). Procedural blank and standard solutions were prepared following method
described by Franson, 1995).
Quality control: Triplicate analyses were performed on the samples to
yield a mean which was used to determine trueness (Valcarel,
2000). Procedural blanks and standard solutions were prepared and included
for analytical quality control to assure the accuracy and reproducibility of
RESULTS AND DISCUSSION
All parameters determined were detected in this study. The mean and range of results obtained from the three months study for the borehole water parameters in the three sampling sites as well as their World Health Organization (WHO) guideline standards are presented in Table 1 and 2.
Pollution index (Pi) is expressed as a function of the concentration of individual parameter as against the baseline standard. It is given as:
It shows the relative pollution contributed by each item. The critical value
is 1.0 values greater than 1.0 indicates significant degree of pollution while
values less than 1.0 shows no pollution.
Pollution index values obtained for calcium and manganese in all samples studied
indicated that the boreholes are polluted with the water showing a higher degree
of pollution in manganese than calcium. The water therefore needs to be treated
before use. However, the results of the other parameters studied were considered
low when compared with the WHO (1983) and FEPA
(1991) for drinking water hence did not indicate pollution because their
levels were below the limits for portable water. A similar trend was observed
in the parameters determined for the samples from the two boreholes studied
in Agbor since no significant variation was observed in their results. This
shows a very strong peculiarity in the physiochemical properties of water from
the boreholes studied. Strong variation in results were observed for some of
the parameters studied between the sampling site in Benin and Agbor which can
be attributed to the difference in geographical location.
The results when compared with similar studies investigating the physicochemical
characteristics of borehole water in warri and environs as reported by Okonkwo
et al. (2008); Rim-Rukeh et al. (2008) shows that
pH was higher in this study indicating that the borehole water are slightly
alkaline as against those in warri which were slightly acidic (5.32-5.34 and
4.50-5.20). Temperature values were lower in this work when compared to boreholes
studied in warri (27.74-28.83 and 26.0-27.0°C). Conductivity values were
found to be significantly higher (62.6-158.40 and 370-410 μs cm-1)
in warri borehole waters than that reported in this work.
|| Mean and range of results of borehole water samples
Values for dissolved oxygen was very similar to those reported by Okonkwo
et al. (2008) (5.52-5.68 mg L-1) and Rim-Rukeh
et al. (2008) (4.9-5.9 mg L-1) in warri. A comparison of the
metals and ion contents in both study shows that nitrate (1.046-4.13 and 18-38
mg L-1), sulphate (5.40-15.68 and 68- 170 mg L-1) and
iron (0.23-0.24 and 13.80-19.32 mg L-1) determined in borehole from
warri had values higher than reported in this study while zinc (0.002-0.013
mg L-1), lead (0.008 mg L-1), cadmium (0.002 mg L-1),
manganese (0.022-0.062 mg L-1), chloride (9.40-17.4 mg L-1)
and ammonium (0.006-1.81 mg L-1) reported by Okonkwo
et al. (2008) gave values that were lower than those reported in this study.
However, values for BOD (14-21 mg L-1), lead (0.10-0.5 mg L-1)
and zinc (0.56-0.98 mg L-1) reported from the work of Rim-Rukeh
et al. (2008) exceeded those reported in this study while the concentration
of nickel (0.01-0.02 mg L-1) was very similar to that in this study.
A comparative evaluation of the present study and those reported by Okonkwo
et al. (2008) as well as Rim-Rukeh et al. (2008)
showed that their results are highly correlated except for pH and conductivity
which showed significant differences as well as the concentration levels of
nitrate, sulphate, iron and BOD reported by Rim-Rukeh et
al. (2008) in warri borehole water which were in orders of magnitude greater
than those reported in this study. The low level observed for most of the parameters
investigated in this work as against the studies conducted in warri could be
due to the low level of industrialization, lack of proximity to possible source
of contaminants and very far reaching water table observed in the study areas.
|| Computation data of pollution index for the three sampling
Since the water table is very low in the study areas, presence of numerous
soil layers will act as natural filters which will reduce contaminant concentration
to a large extent. This could stem from the fact that sand bed (soil profile)
is a natural filter where processes such as filteration, adsorption, biodegradation,
ion exchange and dispersion may reduce concentration of contaminants to a great
extent (Okokoyo and Rim-Rukeh, 2004). Low levels of
ions and metals in this work when compared with the studies in warri could be
due to the non acidic nature of the water because (Etu-Efiofor
and Odigi, 1983) reported that in an area with a pH less than 5, the solubility
of heavy metals is permissible. Similar study on the assessment of dry season
surface, ground and treated water quality in the Cape Coast municipality of
Ghana revealed exceedances to some health-based drinking water guidelines for
various water samples on pH, Fe, Mn, SO42¯, Cu and
Zn (Quagraine and Adokoh, 2010) as against the results
obtained in this work. However, the results from this study when compared with
a study on the assessment of drinking water quality of canal, shallow pumps,
dug wells and water supply schemes from the administrative districts of Thatta,
Badin and Thar in Southern Sindh (Pakistan) shows that the limits for electrical
conductivity, sodium and iron exceeded World Health Organization standards but
other parameters as pH, copper, manganese and zinc were within standard permissible
limits of World Health Organization (Memon et al., 2010).
A total assessment of the overall water quality parameters shows that ground
water from the three boreholes studied are safe for drinking and other domestic
activities by parameters which fell within the allowable WHO
(1983) and FEPA (1991) limits, however values obtained
for calcium and manganese exceeded the recommended standard. This agreed with
the results obtained for the measurements of various water quality parameters
carried out on groundwater samples of dug wells, bore wells and hand pumps at
the northern Indo-Gangetic alluvium region (Singh et al.,
Non treatment of borehole water can bring deadly illness such as typhoid (Mathew,
2003). Hence proactive measures should be taken to advert severe contamination
so as to protect our precious ground water resource.
It is therefore advised that the borehole water be subjected to treatment processes to reduce the concentration of calcium and manganese before exposure to public use.
Water quality parameters in borehole water of University of Benin, Benin-City. Edo State and vicinities around Agbor, Delta State were assessed to evaluate the level and degree of purity of the borehole water. All parameters determined were found. The borehole water were found to be safe in the parameters studied except for calcium and manganese which exceeded acceptable world health limits. Parameters such as pH, temperature, conductivity, BOD, DO, Chloride, Nitrate, Ammonium, Sodium, Magnesium, Sulphate, Lead, Cadmium, Copper, Zinc, Chromium, Arsenic, Iron, Nickel were below pollution levels when compared with the WHO and FEPA maximum allowable levels for drinking water. However, the pollution index for calcium and manganese indicated that the borehole waters are polluted in these metals. It is therefore suggested and advised as a matter of National health importance that the water from the borehole be subjected to purification and treatment processes to reduce calcium and manganese levels before exposure to public use.
It is recommended that appropriate regulatory agencies should carry out quality assessment of existing boreholes to ascertain their quality level of the water before allowing for public utilization.
APHA, 1992. American Public Health Association (Standard Methods for the Examination of Water and Waste Water. 18th Edn., APHA, Washington, D.C.
Ademoroti, C.M., 1986. A Standard Methods for Water and Effluents Analysis. Foludex Press, Ibadan, pp: 18.
Ahn, L.Y., S.H. Lee, K.T. Kim, J.H. Shim and D.Y. Kim, 1996. Baseline heavy metal concentration in the antartic clain, lutemula elliptica in maxwell bay, King George Island, Antartic. Mar. Pollut. Bull., 32: 592-598.
Anawara, H.M., J. Akaib, K.M.G. Mostofac, S. Safiullahd and S.M. Tareqd, 2002. Arsenic poisoning in groundwater health risk and geochemical sources in Bangladesh. Environ. Int., 27: 597-604.
Direct Link |
Anonymous, 1995. Standard methods for the examination of water and wastewater 19th edition. Prepared and Published Jointly by: APHA, AWWA and WEF; Joint Editorial Board; Amold E. Greenberg, Andrew O. Eaton, Lenore S. Cleseri, American Health Association, Washington, DC.
Chapeon, D., 1992. Water Quality Assessment: A Guide to the use of Biota, Sediments and Water in Environmental Monitoring. Chapman and Hall Ltd., London, pp: 58-100.
Etu-Efiofor, J.O. and M.I. Odigi, 1983. Water supply problems in the eastern niger delta. J. Mining Geol., 20: 183-193.
FEPA., 1991. Guidelines and Standards for Environmental Pollution Control in Nigeria. Federal Environmental Protection Agency, Lagos, Nigeria, pp: 54-58.
Franson, M.A., 1995. Standard Methods for the Examination of Waters and Wastewaters. 14th Edn., APHA-AWA-WPCF, New York, pp: 150-162.
Kot, B., R. Baranowski and A. Rybak, 2000. Analysis of mine waters using X-ray fluorescence spectrometry. Polish J. Environ. Stud., 9: 429-431.
Direct Link |
Mathew, P., 2003. Advanced Chemistry. Cambridge Foundation Book, London.
Memon, M., M.S. Soomro, M.S. Akhtar and K.S. Memon, 2010. Drinking water quality assessment in Southern Sindh (Pakistan). Environ. Monit. Assess., (In Press). 10.1007/s10661-010-1616-z
Meranger, J.C., K.S. Subramanaian and C.A. Chalifoux, 1979. National survey for cadmium and magnesium, copper, lead, zinc, calcium and magnesium in Canadian drinking water supplies. Environ. Sci. Tchnol., 13: 707-711.
Okokoyo, P.A. and A. Rim-Rukeh, 2004. Sand bed filteration in refinery wastewater polishing. Multydisciplinary J. Emperical Res., 1: 164-170.
Okonkwo, M.J., H.S. Ottah and H.S. Ukulu, 2008. Comparative study of physico-chemical characteristics of bore holes and hand dug wells in warri and environs, Delta State, Nigeria. Agbor J. Sci. Educ., 3: 280-286.
Quagraine, E.K. and C.K. Adokoh, 2010. Assessment of dry season surface, ground and treated water quality in the cape coast municipality of Ghana. Environ. Monit. Assess., 160: 521-539.
Rim-Rukeh, A., O.G. Ikhifa, P.A. Okokoyo, J.K. Awatefe and M.O. Odjighere, 2008. Physico-chemical characteristics of bore hole water in warri, Delta State, Nigeria. Agbor. J. Sci., 3: 133-140.
Silderberg, M.S., 2003. Higher Education Chemistry. The Molecular Nature of Matter and Change, Mc Graw Hill.
Singh, K.P., A. Malik, D. Mohan, V.K. Singh and S. Sinha, 2006. Evaluation of groundwater quality in northern Indo-gangetic alluvium region. Environ. Monit. Assess., 112: 211-230.
Singh, S. and L.M. Mosley, 2003. Trace metal levels in drinking water on Viti Levu, Fiji Islands. S. Pac. J. Nat. Sci., 21: 31-34.
Sunnudo-Wilhelmy, S.A. and G.A. Gill, 1999. Impact of the clean water Act on the levels of Toxic Metals in Urban Estuaries the Hundson River Estuary Revisited. Environ. Sci. Technol., 33: 3471-3481.
USEPA, 1986. Method by method statistics from Water Pollution (WP) laboratory performance evaluation studies. Quality Assurance Branch, Environmental Monitoring and Support Lab., Cincinnati, Ohio.
Udom, G.J., F.A. Ushie and E.O. Esu, 2002. A geochemical survey of groundwater in Khana and Gokana local government area of Rivers State, Nigeria. J. Applied Sci. Environ. Manage., 6: 53-59.
Valcarel, M., 2000. Principles of Analytical Chemistry. Springer-Verlag Berlin Heidelberg, New York.
WHO, 1983. Guidelines for drinking water quality, technical report series 505, Geneva. http://www.who.int/water_sanitation_health/dwq/gdwq3rev/en/
Young, J.C., G.N. McDermott and D. Jenkins, 1981. Alterations in the BOD procedure for the 15th edition of standard methods for the examination of water and wastewater. J. Water Pollut. Control Fed., 53: 1253-1253.